Satel INTEGRA Plus Dokumentacja Pobierz pdf (Strona 40)

38 Programming SATEL

86. E

NTRY

XIT

–

FINAL

). The alarm from the zone will be delayed by a preset time. This

makes it possible to disarm the partition before the alarm is triggered.

Signaling delay – refers to the 4.

ERIMETER

, 5.

NSTANT

and 6.

XIT

type zones. Loud alarm

signaling can be delayed by a programmed time period.

Alarm delay – refers to the 5.

NSTANT

and 6.

XIT

type zones. The alarm from zone may be

delayed by a programmed time period.

Surveillance time – refers to the 8.

XTERIOR

type zones.

Bypass time – refers to the bypassing zones (zone types 64-79). It indicates for how long

the zones will be bypassed. If value 0 is programmed, the zones will remain bypassed until

disarming the partitions to which they belong, or until they are unbypassed by the user.

Module number (lock/keypad) – refers to the 58. T

ECHNICAL

–

OOR BUTTON

type zones. It

defines which door will be unlocked after zone violation (you can indicate a door controlled

by partition keypad, code lock, proximity card reader expander or DALLAS chip reader

expander).

Arming mode – refers to the 80.

RMING

and 82.

ISARM

type zones. It defines which

type of armed mode will be activated by the zone:

0 – full armed mode;

1 – fully armed and, additionally, the zones for which the B

YPASSED IF NO EXIT

option is

enabled, will be bypassed;

2 - 3.

NTERIOR DELAYED

type zones

will not be armed, 8. E

XTERIOR

will trigger silent alarm,

and the other ones – audible alarm;

3 – same as 2, but the delayed zones type will act as instant ones.

Group – refers to the 80.

RMING

, 81.

ISARMING

and 83.

LEARING ALARM

type zones. It

defines which group of partitions will be controlled by the zone (the zone always controls

the partition it belongs to). If value 0 is programmed, the zone will only control the partition

to which it belongs.

Exit delay – refers to the 89. F

INISHING EXIT DELAY

type zones.

Outputs group – refers to the 92.

UTPUTS GROUP OFF

type zones.

Wiring type – must be selected to match the detector type and how it is connected to the

zone:

0. no detector – no detector is connected to the zone;

1. NC – the zone supports a detector of NC (normally closed) type;

2. NO – the zone supports a detector of NO (normally open) type;

3. EOL – the zone supports a detector of NO or NC type with EOL resistor in the circuit;

4. 2EOL/NC – the zone supports a detector of NC type with two EOL resistors in the

circuit;

5. 2EOL/NO – the zone supports a detector of NO type with two EOL resistors in the

circuit;

6. Roller – the zone supports a roller shutter detector;

7. Vibration – the zone supports a vibration detector (also NC type detector);

8. Follow output – the zone does not support any detectors – its status depends solely on

the status of selected output (physical violations and tampers of the zone are ignored);

9. Roller 2EOL– the zone supports a roller shutter detector with two EOL resistors in the

circuit;

10. Vibration 2EOL – the zone supports a vibration detector (also NC type detector) with

two EOL resistors in the circuit;

11. 3EOL/NC – the zone supports a detector of NC type with three EOL resistors in the

circuit;

1 2 ... 35 36 37 38 39 40 41 42 43 44 45 ... 81 82

Komentarze do niniejszej Instrukcji

Brak uwag

Satel INTEGRA Plus Dokumentacja Strona 40

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Satel INTEGRA Plus