Satel INTEGRA Plus Dokumentacja Strona 62
- Strona / 82
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
60 Programming SATEL
S
IGNAL NEW TROUBLE
;
A
LARM MESSAGES
:
P
ARTITIONS
;
A
LARM MESSAGES
:
Z
ONES
;
– w the status of zones, partitions, alarms, trouble memory and
sing and holding down the dedicated keypad keys (the
d by
function provides information about alarms, bypassed zones,
ode).
n with a wireless device
5.
S
HOW VIOLATED ZONES
;
D
ISPLAY MODE SWITCHING
;
it is not possible to vie
current troubles by pres
corresponding options are disabled and cannot be enabled);
– it is not possible to present information on partition status in the bottom line of keypad
display (relevant parameters in the keypad settings will be automatically modified);
– after entering the user menu by means of the service code, you will get access in the
E
VENTS
submenu to the G
RADE
3
function, which enables viewing the events require
EN 50131 for Grade 3;
– the I
SOLATE
user function is only available to the installer;
– the S
YSTEM STATE
user
troubles and partition status (disarmed or type of armed m
Tamper if no communication with ABAX device (2h) [L.no ABAX=tamp] – with this option
enabled, tamper alarm will be triggered if there is no communicatio
of the ABAX system for 2 hours.
4 Arming options
Warn while arming if trouble
informed of the existing t
[Arm, warn.trb.] – if this option is enabled, the user will be
roubles, if any, when arming the system from keypad.
Display violated/bypassed zones on arming [Arm, view viol] – if this option is enabled, the
user will be informed of the violated / bypassed zones when arming the system from
keypad.
If the system is being armed in the "full + bypasses" mode, bypasses and violations of
the zones for which the B
YPASSED IF NO EXIT
option is enabled are not checked.
If the system is being armed in the "without interior" or „without interior and without
entry delay” mode, bypasses and violations of the 3. I
NTERIOR DELAYED
type zones are
not checked (unless the D
ELAY IN
2&3
TYPE ARMING
option is enabled for the zone).
Do no
a ta
.
control panel detects that the mainboard outputs are overloaded or
g.
t arm if tampered [If tamper] – if this option is enabled, arming will be impossible if
mper is discovered.
Do not arm if battery trouble [If batt. trbl.] – if this option is enabled, arming will be
impossible in case of a battery failure.
Required system reset after verified alarm [If verif. al.] – if this option is enabled, arming
will be impossible after a verified alarm
Do not arm if trouble [If other trbl.] – if this option is enabled, arming will be impossible in
case of a trouble.
Do not arm if outputs trouble [If outs. trbl.] – if this option is enabled, arming will be
impossible when the
devices connected to these outputs are cut off.
Do not arm if reporting trouble [If monit.trbl.] – if this option is enabled, arming will be
impossible in case of any problems with reportin
The options D
O NOT ARM IF TAMPERED
, D
O NOT ARM IF BATTERY TROUBLE
, D
O NOT ARM IF
TROUBLE
, D
O NOT ARM IF OUTPUTS TROUBLE
and D
O NOT ARM IF REPORTING TROUBLE
are
available, when the W
ARN WHILE ARMING IF TROUBLE
option is enabled.
- PROGRAMMING 1
- 2 Programming SATEL 4
- SATEL INTEGRA Plus 3 5
- 1. General 6
- 2. Programming options 6
- 2.1.5 Service mode menu 7
- 6 Programming SATEL 8
- SATEL INTEGRA Plus 7 9
- 8 Programming SATEL 10
- SATEL INTEGRA Plus 9 11
- [n – counter number] 11
- SATEL INTEGRA Plus 11 13
- [n – identifier number] 13
- 12 Programming SATEL 14
- SATEL INTEGRA Plus 13 15
- 14 Programming SATEL 16
- SATEL INTEGRA Plus 15 17
- 16 Programming SATEL 18
- SATEL INTEGRA Plus 17 19
- (only INT-S and INT-SK) 19
- (only INT-SCR) 19
- [n – number of output] 19
- 18 Programming SATEL 20
- SATEL INTEGRA Plus 19 21
- (does not apply to CA-64 DR) 21
- 20 Programming SATEL 22
- SATEL INTEGRA Plus 21 23
- 22 Programming SATEL 24
- 2.2 DLOADX program 25
- 24 Programming SATEL 26
- SATEL INTEGRA Plus 25 27
- 26 Programming SATEL 28
- program 29
- 28 Programming SATEL 30
- SATEL INTEGRA Plus 29 31
- LOADX program 32
- Configuring the GSM module 33
- Initiating a connection 33
- 3. System structure 34
- 3.2.3 Partition parameters 35
- Partition type 36
- Options 37
- 3.3 Zones 38
- 3.3.3 Programming the zones 39
- 3.3.4 Zone parameters 39
- 38 Programming SATEL 40
- SATEL INTEGRA Plus 39 41
- 3.3.5 Zone types 42
- SATEL INTEGRA Plus 41 43
- 3.3.6 Zone options 44
- SATEL INTEGRA Plus 43 45
- 44 Programming SATEL 46
- 3.3.7 Counters 47
- 3.3.8 Bypasses 47
- 4. Outputs 48
- 4.1 Output parameters 49
- 4.2 Output functions 49
- 48 Programming SATEL 50
- SATEL INTEGRA Plus 49 51
- 50 Programming SATEL 52
- SATEL INTEGRA Plus 51 53
- 4.3 Options 54
- 4.4 Output triggering 54
- 4.6 Output disabling 55
- 4.8 Output groups 56
- 4.9 Output state indicating 57
- 4.11 Output testing 57
- 5. System options 58
- 5.2 Printer options 59
- 5.3 Other options 60
- SATEL INTEGRA Plus 59 61
- 4 Arming options 62
- Times 5.5 63
- 5. r parameters 63
- 62 Programming SATEL 64
- 6. Programming the keypads 65
- 64 Programming SATEL 66
- SATEL INTEGRA Plus 65 67
- 66 Programming SATEL 68
- 7. Timers 69
- 8. User schedules 70
- 9. Reporting 70
- SATEL INTEGRA Plus 69 71
- 9.1.2 Advanced options 72
- Identifiers 73
- SIA / TELIM prefix 74
- Events assignment 74
- 9.1.4 SIA-IP 74
- 9.1.6 Event codes 74
- 9.2 Starting the reporting 75
- 9.2.3 GPRS reporting 76
- 10. Messaging 77
- 76 Programming SATEL 78
- 10.2.1 Events assignment 79
- 78 Programming SATEL 80
- SATEL INTEGRA Plus 79 81
- 13. Manual update history 82
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Satel INTEGRA Plus
(27 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji